Safety alert to operators of COMAH oil/fuel storage sites and others storing hazardous substances in large tanks

Published:  06 July, 2010

The following safety alert has been released by the UK’s Health and Safety Executive and is primarily for the attention of those companies operating oil/fuel storage facilities. However, it may also be relevant to other sites storing hazardous substances in large tanks where level gauges are used.

The investigation into the fire and explosion at the Buncefield oil terminal depot on 11 December 2005 is continuing. Enquiries into the workings of the high level safety system to prevent tank overfill have indicated that certain aspects of its installation and testing are critical in ensuring that it works properly. Operators of similar establishments are therefore advised to carry out immediate checks where TAV level switches1 manufactured by Cynergy3 Components Limited and supplied by them, their predecessor companies2, or others, are fitted to their storage tanks.

Operators should check TAV level switches fitted with change over (double throw) reed switches. These switches are normally used in 'de-energise' mode to maintain alarm/trip circuits in 'normal' status.

Amendment June 2010

'Since HSE published the guidance in this safety alert, we have identified that it should also apply to some TAV switches with single pole, single throw (SPST) reed switches, depending on the magnet configuration. The corrective action for these switches is the same as for double throw switches. Operators should check with their suppliers for further information about relevant model types and numbers.'

The switches are tested by using a lever or plate fitted to the head of the switch, which can be raised to simulate a high level of liquid in the tank. If the switch is working, then alarms and trips connected to the switch should operate.

However, it is critical that after carrying out this test that the lever or plate is returned to the correct position and locked into place, using a special padlock supplied by the manufacturer3, and in accordance with the manufacturers instructions. Failure to do this can lead to the switch being inoperative in normal operating mode even though it gives the appearance of functioning normally when tested.

There are a number of this type of switch fitted at tank installations in GB and worldwide. HSE has taken urgent action to bring these details to the attention of operators of similar sites through relevant industry bodies across GB, Europe, the USA, and Canada.

Action required

Operators should check immediately whether they have such switches fitted, and if so:

  • ensure they have all relevant manufacturer's information concerning installation and testing and maintenance;
  • ensure they have records of correct installation, testing and maintenance;
  • ensure they are currently installed in accordance with the manufacturer's instructions, with the locking device properly fitted; and
  • complete these checks as soon as possible.

Where operators cannot confirm that the switches are working correctly, then other temporary measures may be adopted, until the defects can be remedied, to ensure safe operations. For example, close supervision and dipping.

The manufacturer/supplier will be contacting known users and installers of these switches to alert them to this issue and will be providing revised instructions on the safe use, setting, cleaning and maintenance of these switches. HSE has served Improvement Notices on Cynergy3 Components Limited requiring it to carry out this work.


1 (A). F150, F160, F171, 155, 156, 157, 170 (May 1987 - December 1996). (B).14-, B17-, F15-, F16-, S14-, S17- (December 1996 - 2006). This prefix should be readily identifiable on the manufacturer's label fitted to the device e.g. F150 or F16-123-123 etc.

2 Crydom Magnetics Ltd, TAV Engineering

3 As an interim measure for Type A switches a suitable padlock or fixing device or for type B switches a 5mm pin secured by a padlock or chain can be used whilst awaiting the manufacturer's equipment.

General note

Please pass this information to a colleague who may have this Product/ Equipment or operate this type of system/process.

Further information

Any queries relating to the safety alert should be addressed to:

Health and Safety Executive

Hazardous Installations Directorate

Chemical Industry Division

Redgrave Court

Merton Road



L20 7HS

Telephone: 0151 951 4078

  • Operation Florian

Sign up: eMagazine & eNewsletter

The latest issues in your inbox.

Company Profiles

Renka´s Fire Engine No. 1

Firefighting, fast, safe, everywhere. Michael Renka GmbH, based in Germany, is a manufacturer of firefighting vehicles, pumps and rescue equipment.

Waterax - We move water

Trusted by wildland firefighters around the world, WATERAX sets the industry standard by developing innovative, portable fire pumps and water-handling equipment designed to withstand demanding applications and rugged environments.

Big Water Flow for Industrial and Municipal Firefighting Applications

Protecting the lives of the public and firefighters while limiting the structural damage caused in large scale fires is our primary mission

We are committed to improving lives and doing business in the right way

We have a unique mix of capability and culture that we refer to as 3M Science and we strive to develop products that improve people’s daily lives in a multitude of ways.

HazSim - Bringing situational HazMat training to life

HazSim, LLC provides innovative simulation training to ensure your team works safely and effectively. HazSim Pro simulation equipment is in use by hundreds of fire departments, training schools, industrial fire teams, and private trainers across the US, Canada and further afield as well as the US Army.

The ultimate in innovation, quality and service

For 60 years Lehavot has been delivering the world’s most advanced fire detection and suppression automatic systems

Advancing rescue technology

The specialist supplier of quality PPE and Rescue Equipment to Emergency Services.

Revolutionizing fire fighting foam technology

The one-stop resource for fire fighting foam concentrates and custom-designed foam suppression systems hardware.

Trust the best, let us be your foam solution

AUXQUIMIA is a Spanish company whose main activity is the design, manufacture and commercialization of firefighting foam concentrates.

Williams Fire & Hazard Control offers a full line of specialized fire response equipment for oil and gas platforms

From storage tanks and pipeline emergencies to offshore platforms and vessels at sea, Williams' response personnel and specialized equipment quickly address adverse fire emergencies.

The leader in truck-mounted hydraulic platforms

Our mission is to provide the best and the safest solution to professionals that work at height.

If you want quality, you want Zico

Since its inception Ziamatic Corp has provided the men and women of the fire service with products designed to make their jobs safer and easier.

The independent alternative

Dafo Fomtec AB is a privately owned company with head office in Stockholm Sweden and manufacturing in Helsingborg in the south of Sweden.